Spade bit boring a hole through framing lumber

Spade Bits for Wood: Sizes, Speeds and Clean-Hole Technique

A spade bit is the fastest low-cost way to bore a medium or large hole through framing lumber, and it works best when you match the diameter and length to the job, run the drill at the right speed and back the exit side with scrap. Get those three things right and a basic paddle bit gives you tidy holes for cable, pipe and bolts all day. At Polar Tool & Supply we stock spade bits from Irwin and Bosch, and we deliver to jobsites free within 50 miles of our locations, so the right size is on the truck when you need it.

Polar Tool & Supply
polartool.us
Get the Right Spade Bit
Explore professional-grade tools and jobsite essentials, with knowledgeable staff ready to help you choose supplies for your project.
Visit

Key Takeaways

  • Spade bits run from 1/4 in. to 1-1/2 in., and most framing work (cable and pipe holes) lands between 3/8 in. and 1 in.
  • Standard bits are 6 in. long, stubby bits are 4 in., and installer bits come in 12 in. and 16 in. for reaching through multiple studs or plates.
  • Run about 1,500 rpm up to 1 in. and slow down for larger sizes, hold the drill square, and use a side handle on big bits.
  • Clamp a scrap board behind the cut, or finish from the back, to stop splintering where the bit exits.
  • Polar Tool & Supply carries Irwin and Bosch spade bits and offers free jobsite delivery within 50 miles.

Table of Contents

What spade bits are made to do

A spade bit is a flat, paddle-shaped bit with a pilot point in the center and a cutting edge on each side. It is one of the oldest and simplest wood-boring designs, and that simplicity is the point. Fine Homebuilding describes spade bits as a low-cost way for plumbers, electricians and framers to drill medium to large holes. The same article notes that today’s versions go beyond the original flat paddle, with barbed edges, curved paddles and self-feed screw tips.

That is exactly the work they get used for on a jobsite:

  • Running electrical cable through studs and joists
  • Passing PEX or copper supply lines through plates and framing
  • Boring through-holes for bolts, dowels and recessed hardware
  • Opening up a hole fast in softwood, plywood and other general framing material

The Spruce Crafts calls the spade bit the best option for holes up to 1-1/2 in. when you are using a handheld drill. The broad blade and pilot point sit on a 1/4 in. shank that fits a standard chuck or a quick-chuck impact driver. That compatibility is a big reason spade bits live in so many contractors’ pouches.

Spade bit sizes and lengths

Spade bits come in diameters from 1/4 in. to 1-1/2 in. According to Fine Homebuilding’s wood-boring bit test, you can buy them singly or in sets, often in 1/16 in. steps, and they are sold at nearly every box store, hardware store and lumberyard. Length matters as much as diameter:

Style Typical length Best for
Standard 6 in. Studs, joists, general framing
Stubby 4 in. Tight spots, between joists, close to a wall
Installer / extended 12 in. and 16 in. Drilling through several framing members in one pass

The lengths in that table come from the same Fine Homebuilding test, which also notes that these bits are impact-ready with a 1/4 in. hex shank. If you buy a single bit, a 6 in. standard length covers most of what a crew does in a week. Keep a long one in the truck for the day you have to drill through a double top plate and a stud wall in a straight line.

Matching the bit to the pipe or cable

The common jobs are quick to size. Most holes drilled with spade bits are cable and pipe clearances through framing, and a 3/8 in. to 1 in. range covers nearly all of them, according to a spade bit size chart. That is also what the common six-piece sets contain.

For specific materials, PowerToolsToday suggests a 3/4 in. bit for standard 1/2 in. copper or PEX and a 5/8 in. bit for common NM cable such as 14/2 or 12/2. It also says to measure the actual outside diameter of what you are running before you drill. Give the pipe or cable a little clearance so it slides through without binding or rubbing the edges of the hole.

Where the 1-1/2 in. bit fits

The largest standard spade bit is 1-1/2 in. The Bosch 1-1/2 in. x 6 in. Daredevil standard spade bit is the top of the range for a regular 6 in. length. Use it for larger drain, conduit or bundled-cable holes. Pro Tool Reviews notes that for holes above about an inch, bits this size should be run in your drill’s low-speed setting with a side handle on, which we cover below.

Choosing a spade bit for the wood you are drilling

Spade bits are general-purpose cutters. Wood Magazine says they work well for general drilling in both hard and soft woods, and they are a good way to go for holes beyond normal twist-drill size, from 1/2 in. up to 1-1/2 in. They can be bought as small as 1/4 in.

A few practical notes by material:

Softwood framing (pine, fir, spruce). This is where a spade bit is at home. The paddle clears chips quickly and the bit pulls through with light pressure when it is sharp.

Hardwood. Expect to go a bit slower and let the bit do the cutting. Wood Magazine’s speed guidance, covered below, is lower for hardwood, and sharp edges matter more because tight grain increases resistance.

Plywood and sheet goods. Support the exit face. Plywood veneers lift easily, so a backer board makes the difference between a clean exit and a ragged one.

Plywood exit face backed by sacrificial scrap wood

Hole quality. A spade bit scrapes and tears more than it slices, a point made by Wood Magazine, which also says refinements such as Irwin’s Speedbor design aim for faster, cleaner boring. For holes that will be hidden inside a wall, that is plenty. For holes that will show, the backer-board technique below gets you a lot closer to a crisp edge.

Bit design: what has changed

In Fine Homebuilding’s torture test of 13 spade bits in 1 in. diameter and 6 in. length, the Bosch Daredevil, a curved-paddle bit with a self-feed screw tip, was the best overall performer and gave the lowest cost per hole. The screw tip pulls the bit into the wood so you push less, which means less fatigue over a day of drilling through studs. We carry the Bosch 1 in. Daredevil spade bit for exactly that kind of work.

Bosch 1 in. Daredevil Spade Bit

The Irwin 88818 Speedbor spade bit in 1-1/8 in. x 6 in. is a good pick when you need a size between the usual 1 in. and 1-1/4 in. steps.

What drill and shank to use

Most spade bits have a 1/4 in. hex shank. Pro Tool Reviews notes that some can go straight into an impact driver, and that you should use the high-speed gear up to about 1 in. and the low-speed gear for the largest bits. It also recommends a side handle for larger bits, because they can bind and twist your wrist or elbow when the bit catches.

That makes drill choice simple:

  1. Corded or cordless drill/driver with a side handle. The everyday choice. A drill with two speed ranges lets you shift down for big bits.
  2. Impact driver. Fine for hex-shank bits in smaller sizes where you want a quick, compact tool.
  3. Right-angle drill. Useful in tight stud bays, where the stubby 4 in. length also helps.

If your crew is replacing tools or adding batteries, our Milwaukee, Makita, DeWalt and Bosch collections cover the drills and drivers that run these bits, and our staff can help you match a drill to the work. Our batteries collection keeps the charge side covered.

The right speed for each size

Speed is where most poor spade-bit holes start. Wood Magazine’s guidance is to limit speed to 1,500 rpm for spade bits up to 1 in. in hardwood, and 1,000 rpm for larger ones. It adds that Irwin’s Speedbor 2000 bits can run at 1,800 rpm in all sizes.

The Spruce Crafts adds an important correction: running slow is a mistake once the hole is started. Go slow while you position the pilot point and begin the cut, then increase the speed as soon as the hole is started. A bit that is crawling through the wood tends to grab, burn and tear.

Bit size Starting point
1/4 in. to 1 in. High-speed range, about 1,500 rpm in hardwood
Over 1 in. to 1-1/2 in. Low-speed range, about 1,000 rpm in hardwood

These numbers are starting points. If the bit smokes, the wood darkens or the drill labors, back off the pressure and let the cutting edges do the work.

Polar Tool & Supply, 3642 Scheuneman Road, 55110 Gem Lake
Polar Tool & Supply
Find the Right Bit for Your Job
3642 Scheuneman Road, 55110 Gem Lake

How to drill a clean, straight hole with a spade bit

The steps are short. What separates a clean hole from a ragged one is doing each of them every time.

1. Mark the center precisely

Pro Construction Guide advises you to mark the center of the hole clearly and precisely. The pilot point has to sit exactly where you want the hole, so a small punch or a pencil cross with a dimple from an awl helps it stay put.

2. Secure the work

Clamp the workpiece to your bench or sawhorse over a piece of scrap. Wood Magazine tells you to secure the work solidly and clamp it to the table, and to use both hands on a portable drill. A free workpiece can spin if the bit catches, because spade bits generate a lot of torque. In framing that is already fixed in place, brace yourself and keep your body out of the line the drill would swing.

3. Start slowly, then speed up

Set the point on your mark and hold the drill so the shank is at a right angle to the work, as Pro Construction Guide puts it. Start slowly while the spurs and pilot point locate, then bring the drill to full working speed. Pro Tool Reviews says a sharp bit needs only minimal downforce, so if you are leaning on the drill, the bit needs attention or the speed is wrong.

4. Keep the drill square

Watch the drill from two angles, or have someone check you from the side. A spade bit follows the angle you give it, and a hole that wanders is a hole that has to be redrilled.

5. Control the exit

This is the step that decides how the back of the hole looks. The Spruce Crafts describes two ways to avoid blowout on the far side:

  • Clamp a sacrificial board to the back of the workpiece and drill through into it.
  • Drill partway until the pilot point comes through, then flip the board and finish the hole from the other side.

The second method gives a clean edge on both faces and works well on visible work. In framing you cannot always flip the piece, so the scrap-board method or a slow, light final push is your tool.

Keep the bit sharp

The Spruce Crafts states that spade bits must be very sharp to cut well, with cutting edges honed at about 10 degrees. A dull bit pushes and burns instead of cutting, which is how people end up leaning on the drill and getting rougher holes. If a bit starts squealing or you notice heat at the tip, stop and check the edges.

On a busy site, the practical move is to keep spare bits in your most-used sizes so a dull bit does not stall the job. Sets and single bits are inexpensive compared with the time lost to a struggling bit.

Safety checks before you drill

A few habits protect your wrists, your eyes and the work:

  • Use the side handle. Larger bits can bind in the cut and twist the drill hard enough to hurt your wrist or elbow, as Pro Tool Reviews points out.
  • Clamp the work. A big bit can spin a loose board.
  • Wear eye protection. Chips and splinters come off a spade bit quickly. Our safety gear collection has glasses, gloves and hearing protection.
  • Check what is behind the wall. Before drilling into existing framing, make sure you know where wires and pipes run.
  • Use low-speed gear for big bits. Drop to your drill’s low range for sizes above 1 in.

Going deeper: long bits and extensions

When you have to drill through a stack of framing, the installer-length bits in 12 in. and 16 in. save a lot of time. Bosch also offers 6 in. and 12 in. extensions for its spade bits, according to its Daredevil product announcement. Because a longer bit flexes more, keep the drill square, run steady pressure and clear chips by backing the bit out of the hole occasionally on deep cuts.

Where to buy spade bits and get them to the jobsite

If you are stocking up for a framing crew or a remodel, the quickest path is a single order covering bits, fasteners and drill batteries. Polar Tool & Supply has been family-owned since 2007, and our staff can help you choose the right tools for a specific project. We stock Irwin and Bosch spade bits alongside screws, nails and staples, and local businesses get free jobsite delivery within 50 miles of our business locations. Tell us the sizes and lengths you need, and we will get them to you.

Irwin 88818 Speedbor Spade Drill Bit 1-1/8" x 6"

For a starting kit, most crews do well with a few of the common sizes (3/8 in. through 1 in.) in the 6 in. length, plus a long installer bit for deep runs. Add a stubby or two if you work in tight bays.

FAQ

What are spade drill bits used for?

Spade bits bore medium to large holes in wood quickly and affordably. Plumbers, electricians and framers use them for cable and pipe runs, and they are also common for bolt holes and general-purpose boring in softwood, hardwood and plywood.

What size spade bit do I need for PEX or Romex?

A 3/4 in. bit is common for 1/2 in. copper or PEX, and a 5/8 in. bit is typical for 14/2 or 12/2 NM cable, according to PowerToolsToday. Measure the actual outside diameter of what you are running first so it passes through with a little clearance.

How do I stop a spade bit from splintering the back of the board?

Clamp a scrap board tightly to the back of the workpiece and drill through into it. You can also drill until the pilot point appears on the far side, then turn the piece over and finish from the back, as the Spruce Crafts describes.

Can I use a spade bit in an impact driver?

Yes, when the bit has a 1/4 in. hex shank. Fine Homebuilding notes that standard, stubby and installer spade bits are impact-ready with a 1/4 in. hex shaft. Use a side handle on larger bits if you are drilling with a full-size drill.

How fast should I run a spade bit?

About 1,500 rpm for bits up to 1 in. in hardwood and about 1,000 rpm for larger ones, per Wood Magazine. Start slowly to seat the pilot point, then speed up once the hole is started.

Sources

Back to blog
  • Your Trusted Source for Pro-Grade Tools, Fasteners & Jobsite Solutions

    Polar Tool & Supply is your go-to destination for premium construction tools, jobsite supplies, and contractor essentials. From power tools and hand tools to fasteners, safety gear, and jobsite delivery, we stock the brands pros trust—Milwaukee, DeWalt, Metabo HPT, Makita, Stabila, and more. Whether you’re framing houses, finishing trim, or tackling your next big DIY project, we have the tools and expertise to help you get the job done right.

  • Family-Owned, Contractor-Focused Since 2007

    Founded in Minnesota and serving the Midwest and beyond, Polar Tool & Supply is family-owned and operated, with decades of combined experience in the construction supply industry. We know what it takes to keep jobsites running smoothly because we’ve been there ourselves—delivering the right tools, fasteners, and supplies when and where you need them. With physical stores in Minnesota and Wisconsin, plus a robust online shop, we’re committed to supporting local builders, contractors, and homeowners with real service and real solutions.

  • Every Trade, Every Project, Every Jobsite

    Why do contractors, builders, and DIYers choose Polar Tool & Supply? We understand the demands of the jobsite. Whether you need framing nailers, cordless drills, safety gear, or the latest in jobsite technology, our selection is curated for performance, durability, and value. From fasteners to finish saw blades, ladders to layout tools, we offer everything you need for framing, roofing, remodeling, and finishing—plus expert advice and fast, local delivery.

  • 100% Genuine Tools & Supplies – Backed by Service

    At Polar Tool & Supply, we only stock authentic, professional-grade products from the brands you trust. Every tool, fastener, and accessory is handpicked for quality and reliability. Need help choosing the right tool? Our knowledgeable team is here to help, whether you’re shopping online or visiting us in-store. We’re committed to delivering the best service, support, and value for every customer—on every project.